Blinking lights on the IBM Wheelwriter 6 Series II signal battery failure, full storage capacity, printwheel malfunction and other basic problems. Beeper sounds mean that something is wrong with the typewriter. Most issues that come about are easy to solve if you know where to look. Learning how to read the Wheelwriter's lights and sounds correctly can make your troubleshooting and repair tasks less cumbersome. Use a systematic approach that starts with looking at how the machine is powered up.
- Ibm Wheelwriter 3500 Troubleshooting
- Ibm Wheelwriter 3500 Manual
- Ibm Wheelwriter 3500 Ribbon
- Ibm Wheelwriter 3500 Manual Download
Step 1
Correction Tapes for the IBM Wheelwriter Part # 1337765 - $23.50 ea Works on all IBM Wheelwriters Order here: For GRC brand ribbons. $835.00 ONE YEAR WARRANTY. NEW IBM Wheelwriter 3500 by Lexmark $1195.00 ONE YEAR WARRANTY Reconditioned IBM Wheelwriter 1500 $434.95 ONE YEAR WARRANTY. Reconditioned IBM Wheelwriter 30 $429.95 ONE YEAR. View and Download IBM Wheelwriter 5 operator's manual online. Wheelwriter 5 Typewriter pdf manual download.
Remove other appliances from the typewriter's wall outlet and surrounding area. Turn on the typewriter. Alternatively, plug the typewriter into another wall outlet.
Step 2
Check typewriter-to-extension cord connections, if used.
Step 3
Check the batteries if the 'Line Space' lights continually blink. They could be weak, dead or installed incorrectly. Ensure that the wire plug for the battery holder is plugged in completely.
Step 4
Press the 'Del' key and storage area number you want to erase if the 'Store Light' blinks. You can continue to type after you allocate more room for storage. Alternatively, press 'Store' to stop storing data and continue to type.
Step 5
Check the correction tape cassettes, ribbon and printwheel installation if at least one light blinks and the typewriter beeps six times.
Step 6
Turn off the typewriter and then wait at least 45 seconds.
Turn on the typewriter and if blinking lights appear and beeper signals six times again, replace the printwheel. If the problem is not resolved, call for service in your local area.
Warning
- Storage, margins and tab settings will be lost if you turn the typewriter off while you replace batteries.
Video of the Day
More Articles
On occasion, the lights of your IBM Wheelwriter may not come on or character misprints could occur. The good news is that usually most of these issues are easily solvable. Begin your troubleshooting strategy by looking closely at how your typewriter plugs into to a power source. Additionally, you should inspect the quality and installation of certain parts that move when the typewriter is operating. These items that will require attention at some point in time include the printwheel, ribbon and platen.
Machine Is Not Working
Step 1
Check the cord and be sure it is plugged into the outlet securely. If the lights on the IBM still do not come on, continue.
Step 2
Remove all other equipment and appliances from the outlet, but leave the typewriter plugged in. If the lights on the IBM still do not come on, continue.
Plug the typewriter into another outlet and then verify that both the lights in the room and outlet do not automatically turn off at the same time.
Character Printing Problems
Step 1
Check that the ribbon is installed properly and that both sides are evenly pressed down inside the typewriter.
Step 2
Check the printwheel to see if any parts are broken. If so, replace the printwheel.
Step 3
Grab the paper release lever and pull it toward you.
Step 4
Push the end of each platen firmly in place and then push the lever back into place.
Ibm Wheelwriter 3500 Troubleshooting
Step 5
Remove any items that may be blocking the carrier's path.
Ibm Wheelwriter 3500 Manual
Turn off the typewriter and then turn it back on again after one minute has passed.
Warning
- Your typewriter can overheat if the vents on it are blocked or if it is against the wall. Set it away from the wall at no less than 3 inches and apart from warm appliances, such as heaters.